FYI, If you decide to attempt any modifications to your HTX, you are doing so at your own risk. HTX Owners Manual HTX/Albrecht AE Service. Update*** I’m still doing this repair for those who may need it. Here are the specifics. I charge a flat fee of $35 which includes the new mic cord, the. Cat. No. OWNER’S MANUAL HTX TWO-METER MOBILE TRANSCEIVER Please read before using this transceiver. INTRODUCTION Your .
|Published (Last):||21 October 2011|
|PDF File Size:||1.39 Mb|
|ePub File Size:||15.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
Spam Blocked 9, spam blocked by Akismet. You can also set your HTX to limit reception to only those transmissions that include the selected tone. Clearing a Memory Channel. I htx-52 to replace the microphone cable if I wanted to continue to use the radio.
Index of /k/kb1uif/downloads/Service & User Manuals/Radio Shack/HTX
Common Problems and Solutions If your HTX does not seem to be operating properly, check this section for a possible solution.
Thus, a repeater that has an output frequency of Don’t show me this message again. If the HTX does not turn on, even when you are sure the power wire is properly connected to a 12V DC power source, check the fuse and replace it, if necessary. As I mentioned before, the color code is a close match with all conductors except for the lack of a Green conductor in the case of this particular cable so here is how my pinout ended up being on the microphone connector itself.
The HTX includes the selected transmit tone with your transmissions and requires the selected receive tone to open squelch. Tuning to a Frequency.
Radio Shack HTX-252 Manuals
Priority Memory Channel 1—lets you set the HTX to periodically check the frequency stored in Memory Channel 1 and alert you if there is activity on it. ON-AIR — appears when you transmit.
Important notes in this manual have a large exclamation mark! DTMF Memories 1—10 hold 15 digits each. Setting the Scan Options. Setting the Subaudible Tones.
The transceiver begins to scan up or down SCAN the full frequency range. There have been a bunch of them showing up on Ebay thanks to them closing hundreds of RS stores and clearing them out. Tune to the memory channel you want to enable or disable for scanning. Enter the htx-522 five digits of the frequency. If auto-reply is turned on, you must hold down PTT while you transmit.
The frequency gap between the lower and upper scan limits should be no less than two times the current frequency step.
If it gets wet, wipe it dry immediately. Press F, then press MR.
Within this period, we will repair it without charge for parts and labor. Tuning to a Frequency 1.
I ended up having to shave down some of the rubber and use a little dish soap to get it to fit but afterwards it looked like this. Then it checks the secondary fre- quency for second. Repeatedly press scan setting. Enter text from picture: SE —do not resume scanning. Press The offset frequency and appear. Page 29 Subaudible Tone Frequencies Hz The HTX displays St btx-252 the current frequency step. To resume scanning immediately, press MHz. It has 10 DTMF memories which can each hold up to 15 digits for quick transmission.
Just my opinion though, try it out for yourself!
Radio Shack HTX-252 Microphone Cord Replacement
It’s a community-based project which helps to repair anything. The HTX displays tC and the currently set transmit tone. All display elements stay on for about 1 second.
If you do not want a receive tone, select oFF. If you have a super hot iron, then just hold it there for a second while you give the wire a tug or use manuql solder sucker like one of these. The HTX can even scan a selected range and automatically store active frequencies in unused memory locations. Specifica- tions are subject to change and improvement without notice. They then select up to four additional digits unique to each person.